Faber Gres Protector | Stain Barrier For Tiles

Product Description

Faber Gres Protector 


  • Stain-proof protector for all ceramic and porcelain surfaces

  • 100% invisible, low odour, non yellowing and easy to clean

  • It will not enhance the colour of the surface and it will not glaze

  • Its main job is to reduce the surface absorbency & seal it

  • Suitable for indoor and outdoor use & vertical or horizontal 

  • Suitable for all kinds of commercial and residential sealing

  • 1L will cover around 20 to 30 sq meters but it can vary

  • A sealed surface is easier to clean and needs less care

  • Superb protector against coffee stains, wine stains, juices

  • To be applied over a clean, dry and sealant free surface

  • It will provide a few years of protection if maintained properly


Faber Gres Protector | Why Use It


There are very few good sealers for ceramic and porcelain surfaces. The ones that are available are either too glossy or not capable of penetrating the surface. But the new Faber Gres Protector does not have any of these issues. A professional quality solvent based sealer compatible with all ceramic tiles & all matt finished porcelain surfaces. The product will penetrate the tile fully and it will create a barrier between the traffic and the tile. The surface that gets treated with the amazing Faber Gres Protector will have reduced absorbency, it will prevent dark stains from penetrating the surface of the tile and it makes daily cleaning much easier. A professional quality sealer for all commercial and residential porcelain & ceramic tiles.


Faber Gres Protector | How To Use It


Making sure that the surface is spotless and dry is the first step. Always pre-test for compatibility. Do a sample test somewhere in a corner. Apply the product with a flat mopping system or some kind of sealer applicator. Apply the product generously but in an even coat. Allow direct contact with the surface for about 10 minutes then proceed to remove the excess product with a dry cloth or pad. Take your time and try to remove as much excess sealer as you can before the product is fully dry. The surface should be fully dry within 1-2 hours. More porous surfaces will require a second coat. Apply the second coat 2-3 hours later. Same process applies when sealing indoor and outdoor surfaces. Do not mix the product with any other sealers from Faber or other brands. The recommended coverage area is 10-15 sq meters per 1L but in reality the coverage area goes over 20 sq meters per 1L.


Faber Gres Protector | Where To Use It


This sealer was designed to seal and protect ceramic floors and some porcelain floors. It can also be used to seal other types of surfaces like concrete tiles, terracotta, some natural stone floors, etc. When used for sealing outdoor surfaces you should make sure that it has not rained at least 48 hours before the sealing process. The product should be used in 1 coat only but in the case of more absorbent surfaces a second coat might be needed. This product will not affect the original colour of the floor. When applied over dark coloured tiles it might create a slightly richer color. Suitable for residential and professional use.


Faber Gres Protector | Safety


Wear protective equipment and always remember that you are dealing with a solvent based protector. Work in areas with good ventilation and clean all your tools after you are done with the product. Never apply the product to a large area without doing a pre-test. Maintain the surface with Faber cleaners and maintainers.


Faber Gres Protector

Write a review

Note: HTML is not translated!
    Bad           Good

When you order from cleanfast.ie, you will receive a confirmation email. Once your order is shipped, you will be emailed the tracking information for your order's shipment. You can choose your preferred shipping method on the Order Information page during the checkout process.

The total time it takes to receive your order is shown below:

The total delivery time is calculated from the time your order is placed until the time it is delivered to you. Total delivery time is broken down into processing time and shipping time.

Processing time: The time it takes to prepare your item(s) to ship from our warehouse. This includes preparing your items, performing quality checks, and packing for shipment.

Shipping time: The time for your item(s) to tarvel from our warehouse to your destination.

Shipping from your local warehouse is significantly faster. Some charges may apply.

In addition, the transit time depends on where you're located and where your package comes from. If you want to know more information, please contact the customer service. We will settle your problem as soon as possible. Enjoy shopping!