Faber Sol 170 / Solvent Based Water Repellent / 1L

Faber SOL 170 | Solvent Based Water Repellent & Impregnator

• Solvent based, highly concentrated, deep penetrating water repellent

• 100% matt, non glazing, non yellowing, little odour & very easy to use

• Compatible with all unsealed natural stone floors, fittings, statues, etc

• It can be used as a pre-treatment impregnator or as the main protector

• It will prevent water from penetrating the stone, from above and below

• It will maintain its outstanding protection even if the floor is deep cleaned

• The new Faber SOL 170 is a clear matt impregnator with no enhancer

• Suitable for sealing all types of indoor and outdoor natural stone floors

• Cheap, high coverage area, suitable for commercial & residential use

• To be applied on unsealed, clean and dry natural stone floors and tiles

• 1 L of Faber SOL 170 will cover around 30 sq meter of floor/surface

Faber SOL 170 | Solvent Based Water Repellent & Impregnator - Why SOL 170

The amazing Faber SOL 170 | Solvent Based Water Repellent & Impregnator was designed to prevent water & humidity from penetrating from the top or from the bottom. Unlike other similar products, the new Faber SOL 170 | Solvent Based Water Repellent & Impregnator will not affect the natural look of the stone, it will not glaze and it will not be affected by harsh chemicals or acids. Many floor polishing companies apply one coat of Faber SOL 170 | Solvent Based Water Repellent & Impregnator prior to honing the stone floors to prevent deep water penetration. A cost effective and highly efficient solvent based impregnator & water repellent from Faber.

Faber SOL 170 | Solvent Based Water Repellent & Impregnator - Where to use it

The new Faber SOL 170 | Solvent Based Water Repellent & Impregnator is compatible with all natural stone floors, all artificial tile floors that are not glossy or sealed with any type of protectors, with all types of concrete floors and slabs, block walls, terrazzo floors, etc. Use the Faber SOL 170 | Solvent Based Water Repellent & Impregnator to seal and protect indoor and outdoor surfaces. It can be applied in 1 coat system with a flat mopping system or some kind of applicator. Just make sure that the stone is 100% dry before sealing it with the Faber SOL 170 | Solvent Based Water Repellent & Impregnator. A product that will not yellow and it will provide years of protection even in areas with more than usual traffic. This product is in big demand with builders and patio cleaners.

Faber SOL 170 | Solvent Based Water Repellent & Impregnator - How to use it

The surface has to be deep cleaned with one of Faber`s heavy duty alkaline floor cleaners to remove old residue, organic growth, algae, grease, food residue and other types of dirt. Allow time to dry before applying the sealer. When the surface looks 100% dry, you need to prepare for impregnating the stone. The estimated coverage area is somewhere between 20 to 30 sq meters but it can be much higher or much lighter if the surface treated is highly absorbent or has no absorbance at all. Apply enough impregnator until the stone looks wet but not soaked. Don`t worry about the wet look, it will dry up matt when it dries in full. If you manage to miss some areas, no need to worry. You can touch up later. Make sure to remove excess sealer from the stone and do not walk on the surface while the area is drying. 

If you are looking for a wet look or a very glossy natural stone sealer, do not buy the new Faber SOL 170 | Solvent Based Water Repellent & Impregnator. This product will not enhance or create any level of sheen on your floors. Work in well ventilated areas or use an air blower to speed up the drying process. This product is suitable for DIY use as well.

Faber SOL 170 | Solvent Based Water Repellent & Impregnator