You are using an outdated browser. For a faster, safer browsing experience, upgrade for free today.

home-icon

  • Cart

  • Your shopping cart is empty!

 

-easy to use floor stripper that require no training

-fast acting and capable of removing up to 4 coats of polish

-highly active floor stripper that can be used as a floor cleaner

-very affordable floor stripper & very long lasting floor stripper

 

Sure Strip Floor Stripper – How it works

Sure Strip Floor Striper is an easy to use floor stripper that requires no training for use and no special qualification. If the floor that you plan to strip has polish on it Sure Strip Floor Stripper will remove the polish. Like most floor polishes, Sure Strip Floor Stripper can remove up to 4 coats of polish at once but it all depends on the type of polish, condition, age and a few other factors. Most floors should be stripped off in one go but if floors have been re-polished over and over again without stripping then it will take more than one go. Apply Sure Strip Floor Stripper with a mop all over the floor. Do not over saturate wood floors to avoid damaging the wood. Allow up to 5 minutes to work and agitate the polish with a floor pad or a semi hard brush. Remove the waste with a wet vac or a mop. Neutralise the floor with a neutral floor cleaner or vinegar.

 

 

Sure Floor Stripper – Where to use

On all sealed floors. Sure Strip Floor Stripper is a product designed to remove polish and sealant from lino, vinyl, amtico, marmoleum, rubber, ceramic, travertine, terrazzo, marble, sandstone floors etc. If there is polish on the floor this floor stripper will remove it.

 

Sure Strip Floor Stripper – Dilution

1 to 10 should be the right dilution ratio but it could go higher if there is not too much polish on the floor or it can go lower if the floor has a lot of polish on it. Anyway, never use less than 1 to 5. Sure Strip Floor Stripper is a highly active product so never use undiluted to avoid damaging your floor. If you use Sure Floor Stripper for cleaning tile floors you can use a higher dilution to avoid waste. 1 to 50 should do the job.

 

Sure Strip Floor Stripper – Safety

Like any other type of floor stripper, Sure Strip Floor Stripper is a very active product. If used without gloves it can burn badly or it can badly irritate your skin. Wear a pair of gloves for your own protection. Work in well ventilated areas only and avoid any contact with the stripper. If you are stripping floors in an area with no ventilation have another person working with you and wear a fume mask.

 

Sure Strip Floor Stripper- Recommendation

Sure Strip Floor Stripper is a very good floor stripper. It costs little money and it can make you big money. 5L of Sure Strip Floor Stripper should be enough to strip 250 square meters of floor if diluted right. Respect the application periods and all the safety recommendations and you will enjoy the benefits of Sure Strip Floor Stripper.

 

 

Sure Strip Floor Stripper – quality doesn’t have to be expensive!

 

More information about floor strippers:

 

You installed a great, sparkling elegant floor. However, after some time the flooring began to lose its lustre, and even became dull and discoloured. It's time to strip the old wax and replace it with a new coat. It will protect your floor and make it shine. This affects both homes and businesses. For instance, most business premises have hard surface floors, which are high traffic areas for customers and employees. They tend to be one of the dirtiest areas in a building. This is as a result of the dust and dirt that develops, in addition to the scratches from footwear. A clean and well maintained flooring creates a welcoming environment to your future clients or anyone else who will walk into your building. 

 

However, you don't want to be left with a yellow haze after you've gotten rid of the dirt, debris, soil, old stains, and all the old wax; That's why it's important for you to pick the right floor stripper. You also want to use the right chemicals for each hard floor surface.

 

Signs That Your Floor Needs Servicing

Polish removers are used everywhere- from office buildings, theatres, schools and homes, to public buildings, hotels, hospitals, shipyards, and even retail outlets. Here are signs that will tell you whether you need to redo your floor finishing:

 

· Colour change

 

The most common is the floor turning yellow. This is as a result of the dirt imbedding itself into the wax and obscuring the clarity of the wax. Take a picture of the floor before and after the waxing to compare. Alternatively, you can simply check out the parts of your building that are frequented by many people, and compare with the floor of the low traffic areas.

 

· Depressions

Heavy traffic will case dents in the floor. This happens because the protective layer over the floor has been worn out. 

· Divots or scuff marks

If your floor is covered in them, then it needs to be stripped.

 

How To Strip

Before you begin, you need to be sure that you're are committed to completing the entire floor maintenance program. You can't just strip your floor in sections. This is especially for businesses. Stepping in homes is quite easy and you can do everything-from removing the old layer or wax to installing a new finish- in a short time. Floor strippers are usually aggressive and sold by the case. The less often that you strip the floor, the more coats of finish there are to remove. In fact, if you haven't stripped your floor for the past 5 months you may have over thirty coats of wax to remove, it may take a few sessions to deal with all of them. 

 

Choose the best stripper for your floor type, since not all floors are created equal. It's recommended that you check the manufacturer’s instructions on whether the stripper is best suited for resilient or non-resilient floor types. Some types of floor, especially hardwood, can get damaged by certain types of floor finish polish removers. There is a wide variety of different commercial floor strippers on sale. In order to strip the floor, follow these steps:

 

1. Ensure you have the right equipment and supplies for the job. Generally, you'll need a dust mop, several cotton or blend mops, a mop bucket, finish mops, clean trash bags, a floor machine, some black stripping pads plus a wet/dry vacuum. Of course, you'll also need a floor stripper that's suitable for your floor. 

 

2. Line the buckets with heavy-duty trash bags. This is for easy clean-up, and to preserve your buckets for other uses.

 

3. Test the stripper. You need to be sure that you have the right product for your floor. Mix some of the stripper, and then apply it on discrete section of the room, such as an edge that is normally underneath heavy furniture. Floors such as older linoleum ones, can suffer damage or colour bleed when stripped. Testing also lets you see if you've mixed it properly. Allow it to sit for the duration prescribed in the instructions. Remove it and see how well it's worked, and if it has damaged the floor. If there is any issue, halt and find the correct floor stripper for sale for your situation. If it's effective and safe, you can proceed on the rest of the floor. 

 

4. Start in one corner of the room using your mop. You can also pour some stripper and pad it out. Use lots of it, but not too much that till floods your floor and soaks into the seams or cracks. You should apply stripper more generously in areas with a lot of wax build-up. Alternatively, you can work on different sections of your floor at a time.

 

5. Work through the rest of the floor following one general direction, so that you won't have to disturb the stripper that has already been applied. For instance, you can go from the corner furthest from the exit and work your way towards the exit. Apply a lot of stripper to prevent you from damaging the floor.

 

6. Give it time to soak. You can let it air-dry. It can last anywhere between 30 minutes and half an hour.

 

7. Scrub off the old wax. You can do this manually or using an electric floor scrubber. Use tools such as knives and scrubbing pads to scrape away finish at corners. You can your toothbrush for scrubbing the nooks and crannies and the knife to remove the gobs or multiple finish layers in corners.

 

8. Mop to remove the stripping agent. Rinse the floor with warm water and a clean mop, then use cold water. This ensures the complete removal of any remaining residue or floor stripper. Any remaining stripper on the floor would result in the wax peeling off later. Rinsing with cold water helps to tighten up the pores of your floor. 

 

9. Inspect the floor. Check for spots or areas that have wax on them and repeat the procedure on them. You can do this by placing a dark coloured towel on the floor. If there white residue appearing on the towel, then not all has been removed by the stripper. You'll need to treat the areas again. Alternatively, you can pass a putty knife over the flooring. If you see any wax on the knife, you'll need to re-strip those areas. Remember to allow the stripper to dry after each application. 

 

 

How Floor Strippers Work

Floor strippers can be used on various floor types, ranging from resilient, terrazzo and marble, linoleum, vinyl to vinyl asbestos, asphalt, rubber, cork, and sealed wood. You can apply the strippers to the floors using a mop and bucket, floor machine, and a wet/dry vacuum. In case you’re stripping a place with high human traffic, ensure that you completely seal off the area before you begin. Trying to breakdown layer upon layer of floor finish often laid over a number of years can prove to be extremely difficult. This kind of work can be very time consuming with the stripping procedure having to be repeated many times. It's recommended that you don't wait as long to strip the floor. Do it at least every 3 months to prevent a build-up. If the area handles high human traffic, you should carry out the floor stripping process more frequently.

 

Floor stripping basically involves completely removing old wax and finishing found on the floor. Today's products are designed t do most of the job for you. They chemically break down the floor finishing so all you have to do is scrub away the residue

 

Common Ingredients in Floor Strippers

Floor strippers need to break down stuff that’s bonded to the floor, which often involves removing layers and layers of wax. They rely on chemical reactions to break down compounds in the floor polish. As such, they need to be powerful. Some of the common ingredients are: 

 

· 2-Butoxyethanol

It's solvent that with both water soluble and oil soluble properties. Its purpose in the polish remover is to emulsify the floor finish so it you can easily remove it. You can be exposed to this solvent trough skin contact or inhalation. When it permeates into the body, it targets organs such as kidneys and the central nervous system, and overexposure can sometimes cause dizziness. This is why it’s imperative for you to wear proper safety gear when working. A rubber glove ca take you a long way. 

 

· Caustics agents (such as Sodium Hydroxide, Potassium Hydroxide)

Caustic agents are responsible for the high pH of floor strippers. They break down the bonds in the polymerising the finish. When they gets onto your skin it can cause irritation or burn, since they are acids. However, they are needed for the stripper to be effective. Avoid splashing the products onto your skin.

 

· Ammonia

It was among the first chemicals to ever be incorporated n floor strippers. It breaks up the zinc cross-link between polymers. However, it's rarely in use nowadays. Manufacturers are replacing it with substances such as monoethanolamine (MEA). They have the same capabilities, but lack the foul odour for which ammonia is hated.

 

There has been a push for use of greener options when it comes to floor strippers, and there are third-party certifications that give manufacturers requirements to adhere to. Examples are Green Seal and EPA's Design for the Environment. This includes using safer products. For instance, some strippers have replaced 2-butoxyethanol with benzyl alcohol, which is the safer alternative. 

 

10 Important Things You Should Note When Stripping Floors

Nobody wants town a home a floor with old wax on it, or go into a place of business and see a floor that has dirt, stains, and scratches on the floor surface. Getting rid of that unsightly yellow that plagues many buildings is easy using a polish remover, but you need to do it right. Here are things that you should be particular about: 

 

1. Do not use a floor stripper without determining if it’s appropriate for that type of floor. You can check with the manufacturer of the floor or the stripper itself. For instance, the chemicals that can be used on a vinyl composition tile (VCT) floor are not exactly appropriate for a stone floor, and vice versa. 

 

2. Ensure you can effectively strip a floor before trying it out on your client’s floor. This mainly applies to cleaning companies. Stripping is a skill that you need to horn in your own work area before proceeding to your customer's building. 

 

3. Do not forget any tools when you're heading out for the task. This can slow down the process, and you may be tempted to improvise. Using the wrong tool, like housing the stripper in the auto scrub solution tank, can lead to potential damages when you want to use the machine for other cleaning processes,

 

4. Do not use soiled mops and buckets. Not only do they make the strippers work more difficult, but they increase the amount of time you'll have to use scrubbing and getting rid of the residue on the floor. 

 

5. Wear safety gear when using floor strippers. The chemicals can irritate your skin and eyes when they make contact with you. At the very least, you should wear rubber gloved. You can also get goggles, safety slippers or non-slip shoes. 

 

6. If you're a professional cleaner, ensure that you've posted safety cones in the working area. This will prevent people from trumpling all over the floor as you wait for the stripper to dry.

 

7. Do not start working in a large area at a go. This will inconvenience you and most likely result in an improper finish. 

 

8. Ensure that you've properly diluted the stripper as per the instructions on its label. It contains chemicals and they need to be mixed in the right ratios with water for them to be effective. 

 

9. Give a proper dwell time. This is the amount of time that you allow the stripper to air dry before scrubbing it off. Remember not to use fans pointed to the floor. This will hasten the process and cause the product to be ineffective.

 

10. Ensure that your working area is properly ventilated. This is for your safety, and to allow the stripper to dry well.

Overall Rating 0
Write a review
Note: HTML is not translated!
    Bad           Good